Elementary Machine Shop Practice
The book Elementary Machine Shop Practice was written by author Here you can read free online of Elementary Machine Shop Practice book, rate and share your impressions in comments. If you don't know what to write, just answer the question: Why is Elementary Machine Shop Practice a good or bad book?
Where can I read Elementary Machine Shop Practice for free?
In our eReader you can find the full English version of the book. Read Elementary Machine Shop Practice Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Elementary Machine Shop Practice
In our eReader you can find the full English version of the book. Read Elementary Machine Shop Practice Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Elementary Machine Shop Practice
What reading level is Elementary Machine Shop Practice book?
To quickly assess the difficulty of the text, read a short excerpt:
A pointed tool is then FIT SHAFT TO COLLAR 51 used in the tool post as shown in Fig. 56. The point of this tool has an angle of 60, the same as the lathe centers, and is ground like a flat drill so that it cuts on both sides.
After the shaft is centered with this tool, a center-hole about 1/8" in diameter should be drilled. This is done by holding the drill in the tail-stock of the lathe with a drill- chuck, as shown in Fig. 57. The object of this center-hole is to give the center of the shaft ...a bearing on the lathe center a short distance back from the point, as at A in Fig. 58.
Placing Work in Lathe. The work is made to rotate on the lathe centers by fastening a lathe dog to the shaft at the head-stock end, as shown in Fig. 59.
Head Stock tail Stock FIG. 59 There are a number of different sized dogs; the smallest size that will go over the shaft should be used.
The tail-stock center is adjusted so that the shaft will rotate freely, yet be tight enough to allow no slack, or lost motion.
What to read after Elementary Machine Shop Practice?
You can find similar books in the "Read Also" column, or choose other free books by Theron Josiah Palmateer to read onlineMoreLess
To quickly assess the difficulty of the text, read a short excerpt:
A pointed tool is then FIT SHAFT TO COLLAR 51 used in the tool post as shown in Fig. 56. The point of this tool has an angle of 60, the same as the lathe centers, and is ground like a flat drill so that it cuts on both sides.
After the shaft is centered with this tool, a center-hole about 1/8" in diameter should be drilled. This is done by holding the drill in the tail-stock of the lathe with a drill- chuck, as shown in Fig. 57. The object of this center-hole is to give the center of the shaft ...a bearing on the lathe center a short distance back from the point, as at A in Fig. 58.
Placing Work in Lathe. The work is made to rotate on the lathe centers by fastening a lathe dog to the shaft at the head-stock end, as shown in Fig. 59.
Head Stock tail Stock FIG. 59 There are a number of different sized dogs; the smallest size that will go over the shaft should be used.
The tail-stock center is adjusted so that the shaft will rotate freely, yet be tight enough to allow no slack, or lost motion.
What to read after Elementary Machine Shop Practice?
You can find similar books in the "Read Also" column, or choose other free books by Theron Josiah Palmateer to read onlineMoreLess
Read book Elementary Machine Shop Practice for free
You can download books for free in various formats, such as epub, pdf, azw, mobi, txt and others on book networks site. Additionally, the entire text is available for online reading through our e-reader. Our site is not responsible for the performance of third-party products (sites).
Write Review:
Guest
Read Also
8 / 10
User Reviews: