Mechanical Drawing Written for the Use of the Naval Cadets At the United States
Mechanical Drawing Written for the Use of the Naval Cadets At the United States
The book Mechanical Drawing Written for the Use of the Naval Cadets At the United States was written by author Here you can read free online of Mechanical Drawing Written for the Use of the Naval Cadets At the United States book, rate and share your impressions in comments. If you don't know what to write, just answer the question: Why is Mechanical Drawing Written for the Use of the Naval Cadets At the United States a good or bad book?
Where can I read Mechanical Drawing Written for the Use of the Naval Cadets At the United States for free?
In our eReader you can find the full English version of the book. Read Mechanical Drawing Written for the Use of the Naval Cadets At the United States Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Mechanical Drawing Written for the Use of the Naval Cadets At the United States
In our eReader you can find the full English version of the book. Read Mechanical Drawing Written for the Use of the Naval Cadets At the United States Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Mechanical Drawing Written for the Use of the Naval Cadets At the United States
What reading level is Mechanical Drawing Written for the Use of the Naval Cadets At the United States book?
To quickly assess the difficulty of the text, read a short excerpt:
18" Diameter of the outside of the shaft 10" Diameter of the axial hole in the shaft 6" Diameter of the bolt-circle 14" Diameter of the bolts 2 ^" Number of bolts 6 Pencil-work. Draw the center lines. The central point is the center of the shaft.
Ink-work. After the figure is completed, shade the circles.
Draw the center lines and the bolt-circle in red ink.
Dimension the drawing in accordance with the notes under " Dimension Lines. " Mark the centers of the bolt-holes with short full radial li...nes in red ink. These are at right angles to the bolt-circle, thus marking the centers properly. Hatch the section. See "Standard Hatching. ' 1 Legend. The legend is placed in the space left for it and is the same as that for the first sheet, except as follows : SHEET II.
CURVED-LINE DRAWING.
The block lettering is of two types. Curved lines are used where possible.
After the drawing is cut from the board, paper is stretched for the next drawing.
SHEET III. WORKING DRAWINGS.
SKETCHING J VIEWS J CENTER LINES ; PROJECTION ; SECTIONS ; HATCH- ING ; DIMENSIONS.
What to read after Mechanical Drawing Written for the Use of the Naval Cadets At the United States?
You can find similar books in the "Read Also" column, or choose other free books by F W Frank William Bartlett to read onlineMoreLess
To quickly assess the difficulty of the text, read a short excerpt:
18" Diameter of the outside of the shaft 10" Diameter of the axial hole in the shaft 6" Diameter of the bolt-circle 14" Diameter of the bolts 2 ^" Number of bolts 6 Pencil-work. Draw the center lines. The central point is the center of the shaft.
Ink-work. After the figure is completed, shade the circles.
Draw the center lines and the bolt-circle in red ink.
Dimension the drawing in accordance with the notes under " Dimension Lines. " Mark the centers of the bolt-holes with short full radial li...nes in red ink. These are at right angles to the bolt-circle, thus marking the centers properly. Hatch the section. See "Standard Hatching. ' 1 Legend. The legend is placed in the space left for it and is the same as that for the first sheet, except as follows : SHEET II.
CURVED-LINE DRAWING.
The block lettering is of two types. Curved lines are used where possible.
After the drawing is cut from the board, paper is stretched for the next drawing.
SHEET III. WORKING DRAWINGS.
SKETCHING J VIEWS J CENTER LINES ; PROJECTION ; SECTIONS ; HATCH- ING ; DIMENSIONS.
What to read after Mechanical Drawing Written for the Use of the Naval Cadets At the United States?
You can find similar books in the "Read Also" column, or choose other free books by F W Frank William Bartlett to read onlineMoreLess
Read book Mechanical Drawing Written for the Use of the Naval Cadets At the United States for free
You can download books for free in various formats, such as epub, pdf, azw, mobi, txt and others on book networks site. Additionally, the entire text is available for online reading through our e-reader. Our site is not responsible for the performance of third-party products (sites).
Write Review:
Guest
Read Also
7 / 10
9 / 10
User Reviews: