Screw Thread Cutting
Screw Thread Cutting
The book Screw Thread Cutting was written by author Here you can read free online of Screw Thread Cutting book, rate and share your impressions in comments. If you don't know what to write, just answer the question: Why is Screw Thread Cutting a good or bad book?
Where can I read Screw Thread Cutting for free?
In our eReader you can find the full English version of the book. Read Screw Thread Cutting Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Screw Thread Cutting
In our eReader you can find the full English version of the book. Read Screw Thread Cutting Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Screw Thread Cutting
What reading level is Screw Thread Cutting book?
To quickly assess the difficulty of the text, read a short excerpt:
KINKS AND SUGGESTIONS 25 the required number of threads per inch. The tail-stock is then set over either way for a short distance and the taper attachment is set to correspond with the set-over of the tap. The thread is then cut as usual, the tool being set by the face of the tap. The thread cut in this way will be slightly coarser than would have been the case if the centers were in line with the axis of the lathe. The reason for this will be obvious from the cut, Fig. 19, and a little practic...e will enable the machinist to judge just how much the tail-stock should be set over to obtain the required result. For example: If the tap is 10 Fig, 2O. Another Arrangement for Cutting Taps Long in the Lead inches long and is set over % inch, while the tool is moving the whole length of the tap, the movement of the carriage parallel to the axis of the lathe would be through a distance of but 9. 987 inches, so that the thread is lengthened 0. 013 inch; in other words, there are as many threads in 10 inches on the tap as would have been cut in 9.
What to read after Screw Thread Cutting?
You can find similar books in the "Read Also" column, or choose other free books by Erik Oberg to read onlineMoreLess
To quickly assess the difficulty of the text, read a short excerpt:
KINKS AND SUGGESTIONS 25 the required number of threads per inch. The tail-stock is then set over either way for a short distance and the taper attachment is set to correspond with the set-over of the tap. The thread is then cut as usual, the tool being set by the face of the tap. The thread cut in this way will be slightly coarser than would have been the case if the centers were in line with the axis of the lathe. The reason for this will be obvious from the cut, Fig. 19, and a little practic...e will enable the machinist to judge just how much the tail-stock should be set over to obtain the required result. For example: If the tap is 10 Fig, 2O. Another Arrangement for Cutting Taps Long in the Lead inches long and is set over % inch, while the tool is moving the whole length of the tap, the movement of the carriage parallel to the axis of the lathe would be through a distance of but 9. 987 inches, so that the thread is lengthened 0. 013 inch; in other words, there are as many threads in 10 inches on the tap as would have been cut in 9.
What to read after Screw Thread Cutting?
You can find similar books in the "Read Also" column, or choose other free books by Erik Oberg to read onlineMoreLess
Read book Screw Thread Cutting for free
You can download books for free in various formats, such as epub, pdf, azw, mobi, txt and others on book networks site. Additionally, the entire text is available for online reading through our e-reader. Our site is not responsible for the performance of third-party products (sites).
Write Review:
Guest
Read Also
9 / 10
User Reviews: