Toys Their Design And Construction
Toys Their Design And Construction
The book Toys Their Design And Construction was written by author Here you can read free online of Toys Their Design And Construction book, rate and share your impressions in comments. If you don't know what to write, just answer the question: Why is Toys Their Design And Construction a good or bad book?
Where can I read Toys Their Design And Construction for free?
In our eReader you can find the full English version of the book. Read Toys Their Design And Construction Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Toys Their Design And Construction
In our eReader you can find the full English version of the book. Read Toys Their Design And Construction Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Toys Their Design And Construction
What reading level is Toys Their Design And Construction book?
To quickly assess the difficulty of the text, read a short excerpt:
Butt joints are shown in the illustrations opposite CONSTRUCTION BODY. Cut two sides 5" X 2f x ^* with square ends (Fig. 2), then prepare the back 21* x 2i" x ;&* and the front 3* x 2f x &". Carefully cut away the latter for the fitting of the sides, round-off the top edge and bore the three small holes (Figs. I, 3 and 6). Clean up inside faces and glue and pin together, taking care the whole is " square. " To complete the body cut the bottom, which is 4|" x 2^" x iV, then glue and pin it in pl...ace (Fig. I section). Put aside and allow glue to set.
TRACK PIECES. Prepare two 1\" x 2|" x |". From Figs. I and 4 set out the shape, then cut out with bow saw or tenon saw and chisel, finishing with file and glass- paper. To suggest links in the track make light saw-cuts at regular intervals across the edge, and with a sharp chisel enlarge each into a shallow " V " (Figs. I and 7). Now bore two stopped holes as in Figs. 4 and 7 ready for the wheel?.
WHEELS. Cut four \\" in diameter from " plywood.
What to read after Toys Their Design And Construction?
You can find similar books in the "Read Also" column, or choose other free books by Jabez Kay to read onlineMoreLess
To quickly assess the difficulty of the text, read a short excerpt:
Butt joints are shown in the illustrations opposite CONSTRUCTION BODY. Cut two sides 5" X 2f x ^* with square ends (Fig. 2), then prepare the back 21* x 2i" x ;&* and the front 3* x 2f x &". Carefully cut away the latter for the fitting of the sides, round-off the top edge and bore the three small holes (Figs. I, 3 and 6). Clean up inside faces and glue and pin together, taking care the whole is " square. " To complete the body cut the bottom, which is 4|" x 2^" x iV, then glue and pin it in pl...ace (Fig. I section). Put aside and allow glue to set.
TRACK PIECES. Prepare two 1\" x 2|" x |". From Figs. I and 4 set out the shape, then cut out with bow saw or tenon saw and chisel, finishing with file and glass- paper. To suggest links in the track make light saw-cuts at regular intervals across the edge, and with a sharp chisel enlarge each into a shallow " V " (Figs. I and 7). Now bore two stopped holes as in Figs. 4 and 7 ready for the wheel?.
WHEELS. Cut four \\" in diameter from " plywood.
What to read after Toys Their Design And Construction?
You can find similar books in the "Read Also" column, or choose other free books by Jabez Kay to read onlineMoreLess
Read book Toys Their Design And Construction for free
You can download books for free in various formats, such as epub, pdf, azw, mobi, txt and others on book networks site. Additionally, the entire text is available for online reading through our e-reader. Our site is not responsible for the performance of third-party products (sites).
Write Review:
Guest
Read Also
10 / 10
User Reviews: