Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines
The book Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines was written by author Here you can read free online of Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines book, rate and share your impressions in comments. If you don't know what to write, just answer the question: Why is Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines a good or bad book?
Where can I read Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines for free?
In our eReader you can find the full English version of the book. Read Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines
In our eReader you can find the full English version of the book. Read Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines Online - link to read the book on full screen. Our eReader also allows you to upload and read Pdf, Txt, ePub and fb2 books. In the Mini eReder on the page below you can quickly view all pages of the book - Read Book Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines
What reading level is Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines book?
To quickly assess the difficulty of the text, read a short excerpt:
It is customary to set the lock about %6 inch in from the edge to permit of trimming the edge later on if there is trouble from the wood swelling. The center for the boring is located, plus %6 inch as suggested, a bit of the right size is selected, and the hole is bored. The barrel of the lock is then placed in the hole and measurements taken with the knife point around the other parts of the lock. The cut is made with the mallet and chisel. Before putting in the screws, the workman should exam...ine the lock very carefully and see if there are any projecting screw heads or rivet heads that will prevent it laying flat in the work. Cuts should be made to receive all such projections. If the lock is bent the least bit when the screws are tightened, it will cause the key to work very hard and will finally break something.
112 FIFTEENTH EXERCISE.
This exercise is optional — ^that is, the workman can choose any one of the three designs shown in Plates IV, V, and Vr. The general tool work does not include any new tools or processes and, therefore, no explanation is needed other than that given with the drawings.
What to read after Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines?
You can find similar books in the "Read Also" column, or choose other free books by Philippines Bureau of Education to read onlineMoreLess
To quickly assess the difficulty of the text, read a short excerpt:
It is customary to set the lock about %6 inch in from the edge to permit of trimming the edge later on if there is trouble from the wood swelling. The center for the boring is located, plus %6 inch as suggested, a bit of the right size is selected, and the hole is bored. The barrel of the lock is then placed in the hole and measurements taken with the knife point around the other parts of the lock. The cut is made with the mallet and chisel. Before putting in the screws, the workman should exam...ine the lock very carefully and see if there are any projecting screw heads or rivet heads that will prevent it laying flat in the work. Cuts should be made to receive all such projections. If the lock is bent the least bit when the screws are tightened, it will cause the key to work very hard and will finally break something.
112 FIFTEENTH EXERCISE.
This exercise is optional — ^that is, the workman can choose any one of the three designs shown in Plates IV, V, and Vr. The general tool work does not include any new tools or processes and, therefore, no explanation is needed other than that given with the drawings.
What to read after Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines?
You can find similar books in the "Read Also" column, or choose other free books by Philippines Bureau of Education to read onlineMoreLess
Read book Woodworking for Beginners : a Textbook for Use in the Trade Schools And School Shops of the Philippines for free
You can download books for free in various formats, such as epub, pdf, azw, mobi, txt and others on book networks site. Additionally, the entire text is available for online reading through our e-reader. Our site is not responsible for the performance of third-party products (sites).
Write Review:
Guest
Read Also
9 / 10
User Reviews: